ul60950-1 approved
!
"# "
$%
"
&
! ''("
) *!
! 3.6~4.4v voltage adj. range 4.5~5.5v a type:105~185% rated output power b type:105~140% rated output power specification model dc voltage rated current note.2 output line regulation load regulation setup, rise time hold up time (typ.) frequency range efficiency (typ.) input inrush current (typ.) leakage current over temperature safety standards emc emission emc immunity working temp. working humidity storage temp., humidity temp. coefficient vibration mtbf dimension others note packing overload over voltage ac current (typ.) 47 ~ 63hz 1000 cold start <80a(twidth< s measured at 50% ipeak) at 115/230vac <1ma 4.6 ~ 5.4v protection type : hiccup mode, recovers automatically after fault condition is removed refer to en55022 (cispr22) class a -25 ~ +70 (refer to "derating curve") 20 ~ 90% rh non-condensing -40 ~ +85 , 10 ~ 95% rh ) 0.03%/ (0 ~ 60 10 ~ 500hz, 3g 10min./1cycle, 60min. each along x, y, z axes 283.069k hrs min. mil-hdbk-217f (25 ) 86.5% 2.0% 0.5% 2.0% 150mvp-p 4.2v 30a HSN-200-4.2a file name:HSN-200-spec 2014-12-09 +
HSN-200 series ripple & noise (max.) note.3 voltage tolerance note.4 ,
-. !
*#'/ &
*0 "
, *,
"
1
2, #,3 4
*'567" !
*2
)
' , "489 "
, 8,.
, 0,%
!
,
"
, :,.
!
" ; ,.";
) "
$5
, environment safety & emc (note 5) protection withstand voltage isolation resistance i/p-o/p:3.0kvac i/p-fg:2kvac o/p-fg:0.5kvac i/p-o/p, i/p-fg, o/p-fg:100m ohms/500vdc/25 / 70%rh 5.7 ~ 7.0v 86.5% 2.0% 0.5% 2.0% 150mvp-p 5v 30a HSN-200-5a 200w single output switching power supply refer to en61000-4-5; 4kv, criteria a short circuit protection type : hiccup mode, recovers automatically after fault condition is removed 210*62*31mm (l*w*h) protection type : hiccup mode, recovers automatically after fault condition is removed shut down o/p voltage, recovers automatically after temperature goes down 0 ~ 30a current range 0 ~ 30a 126w rated power (convection) 150w 0.55kg; 20pcs/12kg/1.63cuft 1500ms, 100ms/230vac 2500ms, 100ms/115vac 20ms/230vac 16ms/115vac at full load 3.0a/115vac 2.5a/230vac HSN-200-4.2b 4.5~5.5v 2.0% 0.5% 2.0% 150mvp-p 5v 40a HSN-200-5b 0 ~ 40a 200w 3.6~4.4v 2.0% 0.5% 2.0% 150mvp-p 4.2v 40a 0 ~ 40a 168w 180~264vac or 254~373vdc 180~264vac or 254~373vdc voltage range 88% 88% 90~132vac or 254~373vdc 90~132vac or 254~373vdc
pwm circuit detection o.l.p. emi filter power switch- filter & synchronous i/p fg ing converter o.v.p. bridge rectifiers block diagram mechanical specification case no.:232a unit:mm o.t.p. HSN-200 series file name:HSN-200-spec 2014-12-09 rectifiers derating curve static characteristics +v -v 200w single output switching power supply 1 4 3.3 - pin no. 1 3 2 assignment ac/l ac/n ac input terminal(tb1) pin no. assignment terminal 3 2 1 dc output terminal pin no. assignment pin no. 1 2 assignment nc -v terminal input voltage (v) 60hz fosc=90khz io(a) 90 95 100 110 120 132 40 30 20 10 125 180 190 200 220 230 264 240 90~132vac 180~264vac 13 svr1 k led1 tb1 210 62 46.4 7.8 2 206 31 ambient temperature ( ) load (%) -25-100 103040506070 20 40 60 80 100 (horizontal) mount with a 450*450*3mm heatsink dg28c-b-03p-13-00ah 2 3 4 3 4 nc +v cpb-7 m5
HSN-200 series file name:HSN-200-spec 2014-12-09 200w single output switching power supply 1.operate with additional aluminum plate on the bottom.the size of the suggested aluminum plate is shown as below. and for optimizing thermal performance, the aluminum p late must have an even and smooth surface (or coated with thermal grease), and HSN-200 series must be firmly mounted at the center of the aluminum plate. in order to meet the?derating curve?and the ?static characteristics? ,HSN-200 series must be installed onto an aluminum plate(or the cabinet of the same size) installation 2.for heat dissipation, at least 5cm installation distance around the psu should be kept, shown as below: 13 svr1 k 5cm 0 0 5cm 0 m3*4 3 450 450
|
